Step 05TQT does thisAfter PQR · Before WPQ

The written procedure.

WPS

Welding Procedure Specification

The WPS is the instructions your shop welds by. It sets the allowed ranges for metal, filler, position, heat and settings, and it has to sit on an accepted PQR.

$295per WPS · carbon, aluminum, stainless or nickel
MACRO ETCH Macro etch of four numbered T-fillet weld cross sections
The proof under the paper. Fillet welds cut, polished and etched so you can see how deep they fused. Sections numbered in cut order.
In the kitchen

The recipe. The written steps the kitchen follows every time, built on proven ingredients.

Where do you stand?

Are you ready for a WPS?

A WPS can't stand on its own. It sits on an accepted PQR.

You have an accepted PQR

We write the WPS.

Send us the PQR and the joint you're welding. $295.

Request a WPS →

No PQR yet

Start with a coupon.

Weld a test coupon, we test it and write the PQR, then the WPS.

Start at coupons →

PQR vs WPS

One test weld becomes a working range

The PQR records the actual values from one coupon. The WPS turns them into allowed ranges the shop can work within. Values from our sample forms:

PQR · WHAT WAS RUN
WPS · WHAT'S ALLOWED
Thickness
3/8" plateOne coupon
→
1/16" to 3/4"Groove welds, this range
Base metal
SA-516 Gr 70P-No. 1
→
P-No. 1 to P-No. 1Same group of steels
Root opening
3/32"As welded
→
3/32" to 1/8"Set by the WPS

One 3/8" test coupon supports production welds from 1/16" to 3/4" thick.

What's on a WPS

Read a WPS in two minutes

Every section tells the welder what's allowed. The most important line is the one that points back to the PQR.

Sample WPS · TQT Lab QW-482 form, filled with example data for fictional Example Fab Co. For illustration only.
  1. 01

    Supporting PQR No.

    The link to the proof. No accepted PQR here, no valid WPS.

  2. 02

    Process & revision

    Which welding process, and which version of the document this is.

  3. 03

    JointsQW-402

    Groove shape, root opening and backing the welder may use.

  4. 04

    Base metalsQW-403

    Which steels and what thickness range are covered.

  5. 05

    Filler metalsQW-404

    Which rod or wire, by spec and classification.

  6. 06

    PositionsQW-405

    Flat, vertical, overhead: where the weld can be made.

  7. 07

    Preheat & heat treatmentQW-406 · 407

    Minimum temperature before welding, and any treatment after.

  8. 08

    Gas, electrical, techniqueQW-408 · 409 · 410

    Shielding gas, amps and volts, travel speed, stringer or weave.

How it works

From PQR to shop floor

TQT writes it. Your shop runs it.

  1. Send the PQR

    Plus the joint and materials you weld. PQR →

    YOU
  2. We write the WPS

    Ranges set from what the PQR supports.

    TQT
  3. You review & sign

    Your company approves it for use.

    YOU
  4. Qualify your welders

    Each welder tests to the WPS. WPQ →

    TQT

Price

What $295 gets you

PER WPS $295

Carbon, aluminum, stainless or nickel

Request a WPS See all rates →
You send
A copy of the accepted PQR, plus the joint, materials and positions you weld.
You get
A finished WPS as a PDF, plus a hard copy.
Turnaround
Typically 5–7 days. Expedite in 3–5 days for +$50, or rush in 1–2 days for +$200.
Revisions
Small corrections included. A new revision for changed settings is quoted separately.
Needs
An accepted PQR. Don't have one? Start here.

Turnaround

How fast you get your WPS

Typical turnaround is 5–7 days. Need it sooner? Add expedite or rush.

STANDARD5–7 daysIncludedOur typical turnaround.
EXPEDITE3–5 days+$50Moves your job up the line.
RUSH1–2 days+$200For when the job can't wait.

Ask for expedite or rush when you book or call.

Questions

Before you order

Can one PQR support more than one WPS?

Yes. A single PQR can back several WPSs, as long as each stays inside the ranges that PQR supports.

What's the difference between a WPS and a PQR?

The PQR is the record of one test weld and how it tested. The WPS is the working instructions built from it, with ranges instead of single values.

Can I change a WPS later?

Some settings can be revised on the WPS without a new test. Changing an essential variable beyond what the PQR covers means a new PQR first.

Do my welders need anything else?

Yes. Each welder qualifies to the WPS with a WPQ. A good recipe still needs a qualified chef.

Have a PQR? Let's write the WPS.

Send it over, or call and we'll tell you what you need.